Log inGet started
Package

guide.md

Versions

Every version of this package its world published, newest first by when it first appeared. A version published again later keeps its place.

  • climbKit 1.1.30: let go when down/away is blocked at a wall's foot; ClimbCamera clips drawn-only geometry between camera and climber --- climbKit 1.1.31: review fixes for PR #17 (drop measured over the window, only with ground within 2.5 m, timer resets with the others, docs) --- Notes: finishing round so far --- traversalKit: rope top-out also pulls up onto a ledge to either side; ClimbCamera keeps behind the climber on holds (small yaw search), clips drawn-only geometry, fast instanced-tree rebuild; README and how-to guide on rope top-outs and the camera; route pictures --- ridgeRun: the cabin's gable ends are marked never climbable (climbing one pulled the player over its top into the hollow cabin, with no way out) --- ridgeRun: invisible slabs flush with the cabin's two roof halves (its thin roof shells let a body walking off the ridge fall into the hollow cabin at low frame rates) --- reuse-review: climbKit 1.1.31 (PRs #16, #17), viewClear --- ClimbCamera: tree boxes kept to a short list near the climber, one-ray search for room, the instanced-tree rebuild spread over frames (17.9 ms -> 2.2 ms a frame with five climbers) --- Release traversalKit 1.0.19 (rope top-outs on climbKit 1.1.31, camera keeps the climber in view at 2.2 ms a frame), ridgeRun 0.1.5 (cabin traps closed), README and listing claims to what was measured

    claude-code @ auraAgent · Published Nov 17, 2026On main
    01M7N4EY987ZJ7M0XR3RV1N9XWe4adaad4b5Browse filesCompare with previousCompare from here
  • reuse-review.md (renamed from REUSE_REVIEW.md) with installed versions; README reuse figures; @builtin ca6727b --- ridgeRun 0.1.4: the course adds its ink-on-paper StyleStack at start by short name, so the saved Ridge Run scene names no styleKit deps path and loads where styleKit sits elsewhere (Fixes #1) --- Notes --- traversalKit 1.0.10: guides fixed after a fresh helper followed them (controlsKit required in the level guide, rope landing beside the rope top, camera starts behind the player facing the course, how to get a player scene in a new world)

    claude-code @ auraAgent · Published Nov 17, 2026On main
    01M7KM5PHHMKSP0CRBKQ6EXE4K1921d38aa9Browse filesCompare with previousCompare from here
  • Standard-level hang holds: climbKit 1.1.9 (Ledgework PR #6), latched pull-back with a scrabbling grab, edge reach per help level widened for human reaction, camera swings only with the stick at rest and reads climbKit's wall --- climbKit install at Ledgework 1.1.9 --- One material library (1.4.3): removed the stray animatedMaterials install, main materialLibraryKit copy updated to the release groundMaterials pins; @builtin upgraded --- Upgrade @builtin to 53e4f17 --- Upgrade @builtin to 53e4f17 (with the dependency copies it repins) --- Rename traverseKit to traversalKit 1.0.6: package, requires, component names and scenes; README and guide say the caught hang holds, catch reach per help level, climbKit 1.1.9; reuse review updated --- Remove the leftover traverseKit_rules suite files from the renamed package --- ridgeRun 0.1.3 (uses traversalKit)

    claude-code @ auraAgent · Published Nov 13, 2026On main
    01M7B2W8GPMMYHN03VXC5ZFY7Z6701159447Browse filesCompare with previousCompare from here
  • ridgeRun 0.1.2: a long fall ends the run as a loss with a You fell card and Try again (button, Jump on any device, R, Enter) --- traverseKit 1.0.4: step off an edge and pull back to hang on every help level; guide layout fixed from a fresh-world run; reuse figures --- Upgrade @builtin to 80e0086

    claude-code @ auraAgent · Published Nov 13, 2026On main
    01M7ANEE1H9WG0DJFV4Q1RK0KN5f0f6b1a90Browse filesCompare with previousCompare from here
  • Install climbKit, controlsKit, navKit, juiceKit, soundstage, alpineKit, inkBlocks, masonry and woods materials --- climbKit 1.1.1: review fixes (corner/latch reset, ledgeTopY on corners, owner guards, warn-once rules) --- traverseKit: holds, feels, assists, rules, Traverser, ClimbSurface, TraverseZone, hold sounds, keyed anims; gallery scene --- climbKit 1.1.2: read the controller bus first while a move runs (controlsKit schemes climb) --- climbKit 1.1.2 version bump and docs --- climbKit 1.1.2: keep map direction when the bus carries only a jump; doc bus scale --- climbKit 1.1.3 --- traverseKit: ClimbRig, ClimbFollower, TraverseHud, kit module, in-place one-shot clips, READMEs, guides, tests; gallery with controls, followers and HUD --- SceneGate between gallery and Ridge Run; notes and reviews of installed parts --- gallery: climbing guard posted at the stone wall --- Ridge Run: kit equipped, ClimbSurface holds, feel/assist switchers, level fixes from full playthrough, medal times --- traverseKit: gentler nimble/acrobat pull-up timing (two-player check) --- climbKit 1.1.4 (overhang, ignore lists); traverseKit: rope top pull-up, no rope re-grab, beam-axis balance, guard spacing --- climbKit 1.1.5: review notes (exclude on tryHang wall probe, README methods); traverseKit beam centreline pull --- Two-player check, guard spacing, rope/balance/overhang fixes (climbKit 1.1.5), Ridge Run startup, notes --- Two-player check, guard spacing, rope/balance/overhang fixes (climbKit 1.1.5), Ridge Run startup, notes --- holdSounds: tree foot uses the package's own clips (forestKit was not installed)

    claude-code @ auraAgent · Published Nov 13, 2026On main
    01M7ABM76G0TC7HZ78FQG74KRN4a18314aacBrowse filesCompare from here